Nov. 19, 2026
Nitrogen limits at municipal and industrial treatment plants keep tightening, and many operators now run out of carbon in the anoxic zone long before they run out of nitrate. Methanol and sodium acetate are the usual answers, but both bring handling problems: methanol is toxic and flammable, acetate attacks concrete and costs more per unit of COD. Glycerin has moved into that gap over the past decade, and for a plant with a tank, a pump and a nitrogen problem it is often the simplest carbon source to adopt.
Glycerin carries roughly 1.2 g of theoretical COD per gram of product, which is high for a non-hazardous liquid. It is miscible with water at any ratio, has a very low vapour pressure, and does not flash at ambient temperature, so storage and dosing need no explosion-proof classification in most jurisdictions. It is also readily biodegradable and non-toxic to activated sludge at normal dose rates, which matters when a dosing fault sends a slug into the basin.
The trade-off is reaction speed. Glycerin is a three-carbon alcohol that bacteria must first convert to a usable intermediate, so its COD becomes available more slowly than acetate or methanol. In a basin with adequate hydraulic retention time this is an advantage: carbon is released gradually and less of it escapes to the aerobic zone. In a short-retention plant chasing a tight peak, it can be the wrong choice.
Textbook stoichiometry puts the requirement at about 2.86 g of COD per gram of nitrate nitrogen reduced to nitrogen gas. Real plants need considerably more, because dissolved oxygen entering with the recycle stream, cell synthesis and incomplete mixing all consume carbon that never reaches denitrification. Design allowances of four to five grams of COD per gram of nitrogen are common. Converted at the 1.2 figure, a plant removing 100 kg of nitrate nitrogen a day is looking at roughly 330 to 420 kg of glycerin before any safety margin.
Two corrections are worth building into that number. First, dose against the nitrate actually arriving, not the permit limit; an online nitrate analyser pays for itself quickly once glycerin is the carbon source. Second, keep a small trim margin and review it weekly, because a glycerin overdose shows up as rising effluent COD and bulking sludge long before it shows up as a nitrogen problem.
Technical and crude glycerin both work, and the choice is economic rather than biological. Crude material carries methanol, salts and organic non-glycerol matter, all of which add COD but also add chloride and sulphate load and can colour the effluent. Refined technical grade at 99.5 percent is easier to dose consistently and leaves less residue in the tank. Food and pharmaceutical grades are unnecessary for wastewater and add cost without benefit. What matters is batch-to-batch consistency of assay, water content and chloride, because a swinging feed strength turns every dose calculation into a guess.
Glycerin is viscous when cold and viscosity climbs sharply below about 10 C, so outdoor tanks at northern sites need trace heating or a heated dosing line. Diaphragm or progressive cavity pumps handle it well; centrifugal pumps sized for water will disappoint. Diluting to 50 to 70 percent makes pumping easier and improves mixing at the injection point, at the cost of a larger tank. Inject into a zone with local mixing, never into a quiescent corner, and interlock the dose with nitrate measurement so a pump failure is visible in the same shift.
Assay, water, organic non-glycerol matter, chloride, sulphate, colour and heavy metals are the fields that actually affect a wastewater customer. Ask for a batch-specific certificate rather than a generic sample, and confirm the delivery format up front: 1,000 or 1,250 kg IBCs, 200 kg drums, or bulk tanker for sites with fixed storage. Consistent packaging and consistent batch numbering make the receiving check a two-minute job instead of an argument.
SINOFOGROUP supplies refined and technical glycerin for industrial and environmental applications, with batch documentation and export packaging built around the customer's receiving process. Send us your nitrogen load, basin volume and storage arrangement, and we will help size the carbon dose and the delivery plan.
Previous: None
Next: Retention Samples: The Cheapest Insurance in an Oleochemical Supply Contract
Recommend
SINOFO OLEO(GUANGZHOU)GROUP CO.,LTD
Add.: Room 1805, No. 368, Lijiao Road, Haizhu District, Guangzhou, China
Tel: +86 186 6602 3814
Quick Links
Ingredient
Get in Touch
Online
Online Message
Contact
Contact Us: +86 186 6602 3814
E-mail: Mona@sinofo.group
WhatsApp: +86 186 6602 3814